- UNIT, INTERMEDIATE DIRECT
SUPPORT AND INTERMEDIATE GENERAL SUPPORT MAINTENANCE INSTRUCTIONS
- UNIT, INTERMEDIATE DIRECT
SUPPORT AND INTERMEDIATE GENERAL SUPPORT MAINTENANCE INSTRUCTIONS
- UNIT, INTERMEDIATE DIRECT
SUPPORT AND INTERMEDIATE GENERAL SUPPORT MAINTENANCE INSTRUCTIONS
- UNIT, INTERMEDIATE DIRECT
SUPPORT AND INTERMEDIATE GENERAL SUPPORT MAINTENANCE INSTRUCTIONS
- UNIT, INTERMEDIATE DIRECT
SUPPORT AND INTERMEDIATE GENERAL SUPPORT MAINTENANCE INSTRUCTIONS
- WARNING
- TABLE OF CONTENTS
- TABLE OF
CONTENTS-Continued
- CHAPTER 1 INTRODUCTION
- FIGURE 1-1. WAV-850
Gearbox.
- Section II. EQUIPMENT
DESCRIPTION AND DATA
- Table 1-1. Gearbox
Equipment Data
- Section III. PRINCIPLES OF
OPERATION
- FIGURE 1-2. Gearbox
Assembly.
- CHAPTER 2 UNIT MAINTENANCE
INSTRUCTIONS
- Section I. REPAIR PARTS,
SPECIAL TOOLS; TEST, MEASUREMENT, AND DIAGNOSTIC EQUIPMENT (TMDE);
AND SUPPORT EQUIPMENT
- Section III. UNIT
PREVENTIVE MAINTENANCE CHECKS AND SERVICES (PMCS)
- Table 2-1. Preventive
Maintenance Checks and Services
- Table 2-1. Preventive
Maintenance Checks and Services
- Table 2-1. Preventive
Maintenance Checks and Services
- Table 2-1. Preventive
Maintenance Checks and Services
- Table 2-1. Preventive
Maintenance Checks and Services
- Section IV. UNIT
MAINTENANCE TROUBLESHOOTING
- Table 2-2. Unit
Maintenance Troubleshooting
- Table 2-2. Unit
Maintenance Troubleshooting
- Section V. UNIT
MAINTENANCE PROCEDURES
- Inspect Main Reduction
Gear-Port and Starboard.
- Replace/Repair External
Hardware. (FIGURE 2-1)
- Replace/Repair External
Hardware. (FIGURE 2-1)-cont.
- REPAIR
- REPLACEMENT
- FIGURE 2-1. External
Hardware.
- Replace Nonmetallic Hose
Assembly . (FIGURE 2-2)
- REPLACEMENT
- FIGURE 2-2. Hose Assembly,
Dirty Oil.
- Repair Nonmetallic Hose
Assembly. (FIGURE 2-2)
- ASSEMBLY
- Repair/Replace Fluid
Transmission Cooler. (FIGURE 2-3)
- DISASSEMBLY
- REPAIR
- REPLACEMENT
- FIGURE 2-3. Fluid
Transmission Cooler.
- Replace Double Changeover
Filter. (FIGURE 2-4)
- REPLACEMENT
- FIGURE 2-4. Double
Changeover Filter, External View.
- Repair Double Changeover
Filter. (FIGURE 2-5)
- REPAIR
- ASSEMBLY
- FIGURE 2-5. Double
Changeover Filter.
- Replace Control Valve
- FIGURE 2-6. Control Valve.
- Replace Torsional
Coupling. (FIGURE 2-7)
- REPLACEMENT
- FIGURE 2-7. Torsional
coupling
- Section VI. PREPARATION
FOR STORAGE OR SHIPMENT
- CHAPTER 3 INTERMEDIATE
DIRECT SUPPORT MAINTENANCE INSTRUCTIONS
- Section III. INTERMEDIATE
DIRECT SUPPORT PREVENTIVE MAINTENANCE CHECKS AND SERVICES (PMCS)
- '10609.doc' by LOGSA -
Page 1 of 126
- Repair/Replace Main
Reduction Gear - Port and Starboard. (FIGURE 3-1)
- REPAIR
- REPLACEMENT
- FIGURE 3-1. Main Reduction
Gear Removal.
- Repair Control Valve.
(FIGURE 3-2)
- REPAIR
- FIGURE 3-2. Control Valve.
- Repair Torsional Coupling
. (FIGURE 3-3)
- FIGURE 3-3. Torsional
Coupling
- REPAIR
- ASSEMBLY
- Replace External
Input/Intermediate Shafts. (FIGURE 3-4)
- REPLACEMENT
- FIGURE 3-4. External
Input/Intermediate Shaft Group.
- Repair External
Input/Intermediate Shafts. (FIGURE 3-4)
- REPAIR
- Section VI. PREPARATION
FOR STORAGE OR SHIPMENT
- CHAPTER 4 INTERMEDIATE
GENERAL SUPPORT MAINTENANCE INSTRUCTIONS
- Section III. INTERMEDIATE
GENERAL SUPPORT PREVENTIVE MAINTENANCE CHECKS AND SERVICES (PMCS)
- Table 4-1. Intermediate
General Support Maintenance Troubleshooting
- Replace Input Shaft.
(FIGURE 4-1)
- REMOVAL
- FIGURE 4-1. Input Shaft
Replacement.
- Repair Input Shaft.
(FIGURE 4-2)
- DISASSEMBLY
- FIGURE 4-2. Input Shaft
- FIGURE 4-3. Hydraulic Nut
Setup
- DISASSEMBLY-cont.
- REPAIR
- ASSEMBLY
- ASSEMBLY-cont.
- ASSEMBLY-cont.
- Replace Intermediate
Shaft. (FIGURE 4-4)
- REPLACEMENT
- Repair Intermediate Shaft.
(FIGURE 4-5)
- DISASSEMBLY
- REPAIR
- ASSEMBLY
- ASSEMBLY-cont.
- Replace Output Shaft.
(FIGURE 4-6)
- FIGURE 4-6. Middle Casing
and Output Shaft Replacement
- REPLACEMENT
- REPLACEMENT-cont.
- Repair Output Shaft.
(FIGURE 4-7)
- FIGURE 4-7. Output Shaft.
- REPAIR
- ASSEMBLY
- ASSEMBLY-cont.
- Section VI. PREPARATION
FOR STORAGE OR SHIPMENT
- Administrative Storage
- APPENDIX A REFERENCES
- APPENDIX B MAINTENANCE
ALLOCATION CHART
- MAINTENANCE FUNCTIONS.
- EXPLANATION OF COLUMNS IN
TOOL AND TEST EQUIPMENT REQUIREMENTS, SECTION III.
- SECTION II. MAINTENANCE
ALLOCATION CHART
- SECTION II. MAINTENANCE
ALLOCATION CHART
- MAIN REDUCTION GEAR
- SECTION IV. REMARKS MAIN
REDUCTION GEAR
- APPENDIX C
EXPENDABLE/DURABLE SUPPLIES AND MATERIALS LIST
- SECTION II.
EXPENDABLE/DURABLE SUPPLIES AND MATERIALS LIST
- APPENDIX D TORQUE LIMITS
- APPENDIX D TORQUE
LIMITS-cont.
- GLOSSARY
- ALPHABETICAL INDEX
- The Metric System and
Equivalents
- TM-55-1905-223-24-2
- BLANK PAGE
- DISTRIBUTION
- RECOMMENDED CHANGES TO
EQUIPMENT TECHNICAL PUBLICATIONS
|
