| Tweet |
Custom Search
|
|
|
||
 TM 55-1905-217-34P
Code
Definition
position).
(3) Recoverability Code. The recoverability code entered
AF
Item to be assembled at direct support maintenance
in the fifth position indicates the disposition action on
level.
AH
Item to be assembled at general support
unserviceable items.
maintenance level.
Code
Definition
AD
Item to be assembled at depot maintenance level.
XA
Item is NOT procured or stocked because the
Z
Non-repairable item. When unserviceable, condemn
requirements for the item will result in replacement
and dispose at the level indicated in position
of the next higher assembly.
three (3).
XB
Item NOT procured or stocked. If not available
C
Repairable item. When uneconomically repair-able,
through salvage, requisition.
condemn and dispose at organizational level.
XC
Installation drawing, diagram, instruction sheet, or
F
Repairable item. When uneconomically repairable,
field service drawing that is identified by
condemn and dispose at direct support level.
manufacturer's part number.
H
Repairable item. When uneconomically repair- able,
XD
A low mortality item that is not stocked. When
condemn and disposal)se at general support
required, items will be requested and provided
level.
through normal supply channels.
D
Repairable item. When beyond lower level repair
capability, return to depot. Condemnation and
NOTE
disposal not authorized below depot level.
L
Repairable item.
Repair, condemnation, and
Cannibalization or salvage may be used as
disposal not authorized below depot/specialized
a source of supply for any items coded
above except those coded XA and support
repair activity level.
A
Item requires special handling or condemnation
items restricted by AR 700-42.
procedures because of specific reasons (i.e.,
(2) Maintenance Codes. The maintenance code entered
precious metal content, high dollar value, critical
in the third position indicates the lowest maintenance level
material, or hazardous material).
authorized to remove, replace, and use the item. The
b. Federal Stock Number. Indicates the Federal stock
maintenance code entered in the fourth position indicates
number assigned to the item and will be used for
whether the item is to be repaired and identifies the lowest
requisitioning purposes.
maintenance level with the capability to perform complete
c. Description. Indicates the Federal item name. and a
repair (i.e., all authorized maintenance functions). When a
maintenance code is not used in the fourth position, a dash (-)
minimum description required to identify the item. The last
line indicates the reference number followed by the applicable
will be entered.
Federal Supply Code for Manufacturer (FSCM) in parenthesis.
Code
Application/Explanation
The FSCM is used as an element in item identification to
designate manufacturer or distributor or Government agency,
O
Item is removed, replaced, used (third position),or
etc., and is identified in SB 708-42. Items that are included in
complete repair (fourth position) at the
kits and sets are listed below the name of the kit or set with
organizational level.
quantity of each item in the kit or set indicated in front of the
F
Item is removed, replaced, used (third position), or
item name.
complete repair (fourth position) at the direct
d. Unit of Measure (U/M). Indicates the standard or
support maintenance level.
basic quantity by which the listed item is used in performing
H
Item is removed, replaced, used (third position) or
the actual maintenance function. This measure is expressed
complete repair (fourth position) at the general
by a two-character alphabetical abbreviation, e.g., ea, in, pr,
support maintenance level.
etc., and is the basis used to indicate quantities and
D
Item is removed, replaced, used (third position) or
allowances in subsequent columns.
complete repair (fourth position) at the depot
e. Quantity Furnished with Equipment (Basic Issue Items
maintenance level.
Only). Indicates the quantity of the item furnished with the
L
Repair restricted to designated specialized repair
equipment.
activity (fourth position).
f. 30-Day DS/GS Maintenance Allowances.
Z
Non-repairable.
No repairs authorized (fourth
position).
(1) Items authorized for use as required but not for
B
No repair is authorized.
The item may be
initial stockage are identified with an asterisk in the allowance
reconditioned by adjusting, lubricating, etc., at
column.
the user level. No parts or special tools are
(2) The allowance columns are divided into three
subcolumns. The quantitative
procured for maintenance of this item (fourth
vi
|
||
|
||
